Other Factors Affecting Fatigue

Surface Condition (Finish and Treatment)

Surface condition is an extremely important factor influencing fatigue strength, as fatigue failures nucleate at the surface. Surface finish and treatment factors are considered to correct the fatigue analysis results.

Surface finish correction factor

C_{f i n i s h}

is used to characterize the roughness of the surface. It is presented on diagrams that categorize finish by means of qualitative terms such as polished, machined or forged. ¹

Figure 1. Surface Finish Correction Factor for Steels

Surface treatment can improve the fatigue strength of components. NITRIDED, SHOT-PEENED, and COLD-ROLLED are considered for surface treatment correction. It is also possible to input a value to specify the surface treatment factor $C_{t r e a t}$ .

In general cases, the total correction factor is $C_{s u r} = C_{t r e a t} \cdot C_{f i n i s h}$

If treatment type is NITRIDED, then the total correction is $C_{s u r} = 2.0 \cdot C_{f i n i s h} (C_{t r e a t} = 2.0)$ .

If treatment type is SHOT-PEENED or COLD-ROLLED, then the total correction is $C_{s u r}$ = 1.0. It means you will ignore the effect of surface finish.

The fatigue endurance limit FL will be modified by $C_{s u r}$ as: $F L' = F L * C_{s u r}$ . For two segment S-N curve, the stress at the transition point is also modified by multiplying by $C_{s u r}$ .

Surface conditions can be defined in the Assign Material dialog, where you assign them to each part.

Fatigue Strength Reduction Factor

In addition to the factors mentioned above, there are various other factors that could affect the fatigue strength of a structure, that is, notch effect, size effect, loading type. Fatigue strength reduction factor $K_{f}$ is introduced to account for the combined effect of all such corrections. The fatigue endurance limit FL will be modified by $K_{f}$ as: $F L' = F L / K_{f}$

The fatigue strength reduction factor may be defined in the Assign Material dialog and is assigned to parts or sets.

If both $C_{s u r}$ and $K_{f}$ are specified, the fatigue endurance limit FL will be modified as: $F L' = F L \cdot C_{s u r} / K_{f}$

$C_{s u r}$ and $K_{f}$ have similar influences on the E-N formula through its elastic part as on the S-N formula. In the elastic part of the E-N formula, a nominal fatigue endurance limit FL is calculated internally from the reversal limit of endurance N_c. FL will be corrected if $C_{s u r}$ and $K_{f}$ are presented. The elastic part will be modified as well with the updated nominal fatigue limit.

Scatter in Fatigue Material Data

The S-N and E-N curves (and other fatigue properties) of a material is obtained from experiment; through fully reversed rotating bending tests. Due to the large amount of scatter that usually accompanies test results, statistical characterization of the data should also be provided (certainty of survival is used to modify the curves according to the standard error of the curve and a higher reliability level requires a larger certainty of survival).

To understand these parameters, let us consider the S-N curve as an example. When S-N testing data is presented in a log-log plot of alternating nominal stress amplitude Sa or range SR versus cycles to failure N, the relationship between S and N can be described by straight line segments. Normally, a one or two segment idealization is used.

Consider the situation where S-N scatter leads to variations in the possible S-N curves for the same material and same sample specimen. Due to natural variations, the results for full reversed rotating bending tests typically lead to variations in data points for both Stress Range (S) and Life (N). Looking at the Log scale, there will be variations in Log(S) and Log(N). Specifically, looking at the variation in life for the same Stress Range applied, you may see a set of data points which look like this.

S	2000.0	2000.0	2000.0	2000.0	2000.0	2000.0
Log (S)	3.3	3.3	3.3	3.3	3.3	3.3
Log (N)	3.9	3.7	3.75	3.79	3.87	3.9

As with many processes, the distribution of Log(N) is assumed to be a Normal Distribution. The material data input in the Material DB and My Material tabs is based on the mean of the scatter.

The experimental scatter exists in both Stress Range and Life data. In the Assign Material dialog, the Standard Deviation (or Standard Error) of the scatter of log(N) is required as input (SE field for S-N curve). Any normal distribution is fully defined by specifying the mean and its standard deviation, in the case of S-N fatigue analysis in HyperLife, the mean is provided by the S-N curve as $\log (N_{i}^{50 %})$ , whereas, the standard deviation is input via the SE field in the Assign Material dialog.

If the specified S-N curve is directly utilized, without any perturbation, then the mean values of the normal distributions at each data point is assumed to be used, leading to a certainty of survival of 50%, by default. This is a consequence of S-N material data that is available for the mean values of log(N). Since a value of 50% survival certainty may not be sufficient for all applications, OptiStruct can internally perturb the S-N material data to the required certainty of survival defined by you. To accomplish this, the following data is required.

Standard Deviation (Standard Error) of log(N) normal distribution (SE in Assign Material).
Certainty of Survival required for this analysis (Certainty of Survival in the Fatigue Module context).

A normal distribution or gaussian distribution is a probability density function which implies that the total area under the curve is always equal to 1.0. log(N) values which are higher than the mean are always more conservative. Therefore, for certainty of survival calculations, any value greater than 50% implies that the log(N) values lower than the mean are being considered. The total area of the curve starting from the right end of the Normal curve (which is typically positive infinity for a PDF) is directly equal to the certainty of survival (or probability of survival).

A typical normal distribution is characterized by the following Probability Density Function:(1)

P (x) = \frac{1}{\sqrt{2 π σ^{2}}} e^{- \frac{{(x - μ)}^{2}}{2 σ^{2}}}

Where,

$x$: The sample value ( $\log (N_{i})$ ) for which the probability of occurrence is calculated in a particular range (based on the specified certainty of survival).
$μ$: The mean $\log (N_{i}^{50 %})$
$σ$: The standard deviation (or standard error, given by SE field ).

The area of the curve from the right end can be understood to be equal to the certainty of survival specified in the Certainty of Survival field. This integral equation can be solved directly to generate the value of

x

(or

\log (N_{i})

) which will allow a perturbation of the S-N curve. However, the general practice is to convert the normal distribution function into a standard normal distribution curve (which is a normal distribution with mean=0.0 and standard error=1.0). This allows us to directly convert the certainty of survival values into corresponding

\log (N_{i})

values (via Z-tables).

Note: The certainty of survival is equal to the area of the curve under a probability density function between the required sample points of interest. It is possible to calculate the area of the normal distribution curve directly (without transformation to standard normal curve), however, this is computationally intensive compared to a standard lookup Z-table. Therefore, the generally utilized procedure is to first convert the current normal distribution to a standard normal distribution and then use Z-tables to parameterize the input survival certainty.

The equation used to convert the normal distribution to a standard normal distribution is:(2)

z = \frac{x - μ}{σ}

This transformation leads to a corresponding standard normal distribution with a mean of 0.0 and standard error of 1.0. Replacing the values with fatigue data, and rewriting the equation.(3)

\log (N_{i}) = \log (N_{i}^{50 %}) + z * S E

The value of

z

is procured from the standard normal distribution Z-tables based on the input value of the certainty of survival (which is the area under the curve from the right end of the curve up to the corresponding negative Z-value). Some typical values of Z for the corresponding certainty of survival values are:

Z-Values (Calculated): Certainty of Survival (Input)
0.0: 50.0
-0.5: 69.0
-1.0: 84.0
-1.5: 93.0
-2.0: 97.7
-3.0: 99.9

Based on the above example (S-N), you can see how the S-N curve is modified to the required certainty of survival and standard error input. This technique allows you to handle Fatigue material data scatter using statistical methods and predict data for the required survival probability values.

References

¹ Yung-Li Lee, Jwo. Pan, Richard B. Hathaway and Mark E. Barekey. Fatigue testing and analysis: Theory and practice, Elsevier, 2005)