Inspire Reader

Supported Entities

Entities supported by the Inspire reader.
  • Models
  • Assemblies
  • Parts
  • Solids
  • Sheets
  • Curves
  • Points
  • Axis Systems
  • Alternatives
    • Active alternatives are imported by default.
    • All alternatives are imported when hidden (blanked/no show) entities are imported.
The following properties associated to entities are supported:
  • Visibility
  • Color
  • Transparency
  • Active status
    • Active geometry is imported by default.
    • All geometry is imported when hidden (blanked/no show) entities are imported.

Import Options

The Inspire reader uses the inspire_reader.ini file.
@BodyIdAsMetadata
Value Description
on Assign body identifier as metadata.

BODY_ID
off Do not assign body identifier as metadata (default).
@CleanupTol
Value Description
double A negative value (default) indicates to use the auto cleanup tolerance. A value greater than the calculated auto cleanup tolerance indicates to use that specific tolerance. Refer to the CAD Cleanup Tolerance.
@ColorsAsMetadata
Value Description
integer

Read color attributes of geometric entities as metadata with integer values.

COLOR_RGB
on

Read color attributes of geometric entities as metadata.

COLOR_RGB
off Do not read color attributes (default).
@CreationType
Value Description
Parts Generate a full part-based hierarchy.
BOMOnly Generate an empty part-based hierarchy.
TreeOfComponents Generate an assemblies/components based hierarchy.
PackIntoSinglePart Consolidate hierarchy into a single part.
@DensityAsMetadata
Value Description
on

Read density value as metadata (default).

DENSITY
off Do not read density value.
@DoNotMergeEdges
Value Description
on Preserve the original geometry edges, instead of merging them together during the import cleanup phase.
off Merge edges together during the import cleanup phase (default).
@ExtractManifoldFromGeneralBody
Value Description
on Extract the manifold body from a Parasolid general body that is non-manifold and/or of mixed topological dimensionality (default).
off Extract Parasolid general bodies as defined.
@ImportBlanked
Value Description
on Import entities that are hidden, blanked, or no show.
off Do not import entities that are hidden, blanked, or no show (default).
@ImportForVisualizationOnly
Value Description
on

Import the model for visualization purposes only.

This skips many of the import steps (cleanup, stitching, solid creation, and so on) to provide a faster import. The resulting model may not be suitable for other uses.
off Import the model in the normal fashion (default).
@ImportFreeCurves
Value Description
on Import free curves (wireframe entities) into the model (default).
off Do not import free curves.
@ImportFreePoints
Value Description
on Import free points into the model (default).
off Do not import free points.
@LegacyHierarchyAsMetadata
Value Description
on Generate metadata with the original CAD hierarchy within the part.

LEGACY_HIERARCHY
off Do not generate metadata with the original CAD hierarchy within the part (default).
@MetadataPrefix
Value Description
string The string is prefixed to all metadata names. No prefix is used by default.

See CAD Metadata Naming for more details.
@OriginalldAsMetadata
Value Description
on Import original Inspire and Parasolid entity IDs as metadata.
off Do not import original Inspire and Parasolid entity IDs as metadata (default).
@ScaleFactor
Value Description
double Define the model scaling factor during import.

Default is 1.0.
@SkipCreationOfSolid
Value Description
on Read surfaces, but do not create solid entities.
off Create solid entities (default).
@SplitComponents
Value Description
Body Generate body-based component (default if CreationType=Parts).
Part Generate part-based component.
General Keep component as in CAD (default if CreationType=TreeOfComponents).
@SplitPeriodicFaces
Value Description
on Split periodic surfaces to improve the quality and robustness of the import (default).
off Import periodic surfaces as a single surface with a seam edge.
@TargetUnits
Value Description
CAD units Keep the units of the CAD files (default for GUI).
MKS [m kg N s] Convert to the corresponding units system.
MMKS [mm kg N s] Convert to the corresponding units system.
MPA [mm t N s] Convert to the corresponding units system.
CGS [cm g dyn s] Convert to the corresponding units system.
MMKNMS [mm kg kN ms] Convert to the corresponding units system.
MMGNMS [mm g N ms] Convert to the corresponding units system.
IPS Std [in pounds lbf s] Convert to the corresponding units system.
IPS Grav [in slinch lbf s] Convert to the corresponding units system.
FPS Std [ft pounds lbf s] Convert to the corresponding units system.
FPS Grav [ft slug lbf s] Convert to the corresponding units system.
Scale factor Apply the corresponding scale factor (default for no GUI to allow supporting legacy scripts).
@UniqueIdAsMetadata
Value Description
on Split periodic surfaces to improve the quality and robustness of the import (default).
off Import periodic surfaces as a single surface with a seam edge.

Supported Metadata

Metadata generated from the Inspire reader.
BODY_ID
Type Entities Description
string
  • points
  • lines
  • surfs
 Identifier of the CAD body containing the entity.

Generated when @BodyIDAsMetadata=on
COLOR_RGB
Type Entities Description
string

points

lines

surfs

solids

Three RGB values, ranging from 0 to 255, indicating the color of the entity in the CAD model.

Generated when @ColorsAsMetadata = on
DENSITY
Type Entities Description
double solids

The value of the density of a solid.

Generated when @DensityAsMetadata = on
LEGACY_HIERARCHY
Type Entities Description
string
  • points
  • lines
  • surfs
 Hierarchy of an entity within a part.

Generated when @LegacyHierarchyAsMetadata=on
MODELUNIT
Type Entities Description
integer
  • comps
  • parts
 Model units specified in the CAD file.
  • 1 = inches
  • 2 = millimeters
  • 4 = feet
  • 5 = miles
  • 6 = meters
  • 7 = kilometers
  • 8 = mils
  • 9 = microns
  • 10 = centimeters
  • 11 = microinches
  • 12 = decimeters
  • 13 = yards

This is always generated.
ORIGINAL_ID
Type Entities Description
string

comps

points

lines

surfs

solids

parts

The original Inspire ID for comps and the Parasolid entity IDs for the geometry.

Generated when @OriginalIdAsMetadata = on
UNIQUE_ID
Type Entities Description
string

points

lines

surfs

solids

A combination of the Inspire body ID and the Parasolid entity ID.

Generated when @OriginalIdAsMetadata = on